• -20%
POLYURETHANE Pool Varnish (Waterproof)
Barniz Mate
POLYURETHANE Pool Varnish (Waterproof)
Barniz Mate

POLYURETHANE Pool Varnish (Waterproof)

€64.03 €80.04 -20%
Tax included

2 C ACRYLIC POLYURETHANE RESIN 

GREAT ADHERENCE AND HARDNESS

WATERPROOF Polyurethane varnish for all types of supports

It provides great adhesion, great toughness and chemical and mechanical resistance to external aggression from floor sweepers and high pressure cleaners.

It allows the permanent impounding of water, manufactured with polyurethane resins that support the chlorination and maintenance products of swimming pools, even those with salt water.

Especially suitable for varnishing and protecting sand pool liners, or waterproofing pools or jacuzzis made of gresite or tiles with small leaks.

On non-porous surfaces it is advisable to previously apply a 2C Primer

We recommend reading the instructions for use below, for its correct application.

KILOS
  • 5 KGS (SET 4 + 1)
  • 3.35 KG (SET 2.6+0.75)
  • 16 KG (SET 13 +3 )
Color
  • transparent
FINISH
  • Matee
  • Satin
  • Very brilliant

 

IF YOU WANT TO KNOW MORE ABOUT TWO COMPONENT PAINT CLICK HERE

IF YOU WANT TO KNOW MORE ABOUT TO PAINT MUST APPLY, CLICK HERE, PLEASE NOTE THE MOST APPROPRIATE TO SITUATION varnish.

.

IF YOU WANT TO KNOW MORE ABOUT HOW TO PAINT OR VARNISH A POOL CORRECTLY, CLICK HERE

 

IF YOU WANT TO KNOW HOW YOU CAN LOCATE WATER LEAKS OR REPAIR A POOL WITH WATER LEAKS, CLICK HERE

 

 

COMPOSITION OF WATERPROOF POLYURETHANE VARNISH FOR POOLS


Two-component polyurethane varnish, based on a hydroxylated acrylic resin system crosslinked with aliphatic polyisocyanates.

 

CHARACTERISTICS OF POLYURETHANE VARNISH 2 C WATERPROOFING


Indicated for the completion and protection of interior or exterior surfaces , it provides great adhesion and flexibility, as well as great hardness and chemical and mechanical resistance

  • Colorless polyurethane resin for waterproofing swimming pools

  • Adheres to all types of surfaces (stoneware, ceramic, tiles ...)

  • Chemical resistant waterproofing

  • Resistant to the most adverse weather conditions and external aggression.

 


WHERE TO USE TWO-COMPONENT POLYURETHANE VARNISH?


Flexible and transparent waterproofing  for all types of pools, whether made of: stoneware, tile, ceramic, sand pool liners, etc ...

It can be applied on tile or tile coverings, we recommend the prior application of a 2C EPOXY PRIMER FOR NON-POROUS SURFACES 

It can be applied directly, on coatings of concrete, sand, silica, or any type of porous support, etc ...

Recommended for the protection and decoration of wood, of all types of metal surfaces, and on some plastic or PVC surfaces, also on light metals (Aluminum, galvanized, glass) both for interior and exterior.

It can be used as a two-component polyurethane primer, for plastics or irons with difficult anchoring.

 


HOW TO USE THE WATERPROOF TWO-COMPONENT POLYURETHANE VARNISH FOR POOLS?

We recommend waiting between 24 and 72 hours, after emptying the pool, for a perfect drying of the same, before painting.

 And wait again between 5 days and two weeks, after painting or varnishing it to refill the pool with water, for a correct application. (The longer we can let it dry, the better). The maximum hardness of the product is reached after 7 days of application.


- The surfaces to be painted must be free of dust, grease and old paints or varnishes.

-If you have used salfumán or another type of strong water to clean the support or open the pore, you must clean the area with  cleaning solvent or soapy water, several times, to remove the silicones that these products leave on the surface and can repel the varnish.

- For non-porous substrates, it is advisable to apply a two-component epoxy primer for non-porous surfaces beforehand.


- Mix the two components in a 4: 1 ratio and homogenize the contents of the container, stirring thoroughly.


- The application can be done with a brush, roller or air-less. For the waterproofing of swimming pools, it is recommended not to use Air-less, to improve the adherence of the product.


- The first coat will be applied by diluting 25% with our Polyurethane Solvent; for subsequent coats it will be diluted approximately 10%.

- For the waterproofing of swimming pools, it is advisable to apply at least three coats, the third coat, also diluted to 10%


- To achieve good adhesion between coat and coat, do not allow more than 24 hours to elapse.

-Let it dry properly before painting and before filling with water (minimum 72 hours). We recommend waiting 7 days before filling it

 


PRECAUTIONS WHEN USING TWO-COMPONENT POLYURETHANE VARNISH

 

Carry out good ventilation of the premises and have a good extraction system.

Use an activated carbon mask, safety glasses and protective gloves during application.

Dilute the varnish appropriately as indicated in the technical sheet.

Do not apply thick layers, so as not to bleach the support.

Let the varnish dry between coats so that no blisters or bubbles appear.

We recommend not painting in the central hours of the day. so as not to cause a very fast drying when the support is very hot. (Best to apply first thing in the morning)

Avoid applying with a very high relative humidity in the environment or with pink, contact with water, prevents a perfect anchoring of the varnish, and can cause glazes. Substrate humidity must be less than 5%

It should not be mixed or diluted with any other product or substance as the basic characteristics may be altered.

Do not use on paints or varnishes that are not two-component, as it could remove them.




PRESENTATION OF THE FIREPROOF POLYURETHANE VARNISH FOR POOLS


It comes in packages of:

For GLOSS, SATIN finish containers 

Component A: 2.6 kilos and 13 kilos

Component B: 0.75 Kilos and 3 kilos

 

 

We guarantee the quality of our products in accordance with our general conditions of sale and supply.

The technical advice for the use and use of our products is given according to our best knowledge and information, the result of the tests carried out in our laboratories and our experience gathered over the years at the service of the client.  

 

If you want to know the PRICE OF THE POLYURETHANE VARNISH, OF TWO COMPONENTS TO WATERPROOF SAND POOLS OR GRESITE POOLS OR TILES THAT HAVE FILGRATIONS .. you can consult it at the beginning of this page.

 

 

#Buy two-component polyurethane varnish WATERPROOF FOR SAND, GRESITE OR TILE POOLS

# TRANSPARENT polyurethane for WATERPROOFING POOLS

  

.

Theoretical performance
4 to 6 LITER M2 X X HAND
Repainted
  Minimum 8 hours / maximum 24 hours (elapsed this period, it is necessary to sand the surface for repainting)
FINISH
Brightness / Satin
Solvent
Disolvente Poliuretano
Useful of Application
BRUSH / ROLLER / AIRLESS
Cleanliness Tool
Solvent Polyurethane
Dissolution of the first hand
Between 20 % and 25 %
Dissolution in the second hand
10% Solvent
Color
Transparent or colorless
Kilos
JUEGO 2.6 K Y 0.75 KGS / JUEGO 13 K Y 3KGS
Time of dried to a temperature of 25 ºC and a relative dampness of 50 %
TOUCH: 1 hour
Temperature of Application
Do not apply below 5 ° Celsius
Proportion of the mixture
4: 1 (4 Epoxy parts: 1 part catalyst)
Density
0.90 - 1 grs / m3
certificado
Flame retardant B-s2, d0
Humedad del soporte
Inferior al 5 %
Irupol s

You might also like

Reviews Reviews (0)

Based on 0 reviews - 0 1 2 3 4 0/5

The customer has rated the product but has not posted a review, or the review is pending moderation

Product added to wishlist

Portes Gratis Angar para pedido + 75 €

iqitcookielaw - module, put here your own cookie law text