EPOXY DISOLV primer. (Non-porous soil)
EPOXY PRIMER 2C TO SOLVENT
Two-component epoxy primer, INCOLORA, for low-porous concrete floors.
On it you can apply epoxy and polyurethane paints .
Seals and consolidates cement floors in poor condition .
It is applied on floors that have little absorption, to ensure the subsequent anchoring of the paint.
BUY TRANSPARENT OR COLORLESS PRIMER, EPOXY OF TWO COMPONENTS TO THE SOLVENT, FOR FLOORS OF FRESH CONCRETE OR PULIC OR WITH DIFFICULT ANCHORAGE
NATURE OF THE PRIMER FOR SOILS OF EPOXY 2C
Colorless two-component primer based on solvent based on an epoxy-polyamide system.
CHARACTERISTICS OF THE EPOXY 2C PRIMER TO SOLVENT
System used as a two-component primer with excellent wetting properties , especially suitable for low-porous concrete supports, floated by helicopter or polished.
Its function is to ensure a perfect union between the support and the paint for the chosen flooring.
Primer to improve the anchoring of the finishing paint in vitrified or baldosin catalan floors.
WHERE CAN I APPLY THE TWO-COMPONENT EPOXY PRIMER TO SOLVENT?
Used as a connecting bridge between pavements ( epoxy or polyurethane) to mortar and concrete supports .
Also as a sealer and consolidator of cementitious pavements in poor condition.
As a base for painting with a solvent-based two-component finishing paint, either two-component epoxy or two-component polyurethane.
HOW SHOULD THE TWO COMPONENT EPOXY PRIMER BE USED FOR SOLVENT FOR SOILS?
The surface to be painted must be free of dust, grease, old paint and completely dry.
Mix the two components in a 2: 1 ratio and homogenize the contents of the container, stirring thoroughly with a low-speed agitator to avoid introducing air.
On concrete or new cements will have to wait for its total setting, approximately 30 days.
The application can be done with brush, roller or air-less.
It can be applied to the use or by diluting the product with 10% Epoxy solvent. On non-rough substrates, dilute the product with 10% of our epoxy solvent.
The humidity of the support must be less than 10%
Epoxy or polyurethane pavements can never be applied after 36 hours.
PRECAUTIONS WHEN APPLYING THE EPOXY 2C PRIMER TO THE SOLVENT
Perform good ventilation of the premises and have a good extraction system.
Use active carbon mask, safety glasses and protective gloves during application.
PRESENTATION OF THE EPOXY 2C PRIMER TO THE SOLVENT
It comes in containers of:
Component A: 4 kilos and 8 kilos
Component B: 2 kilos and 4 kilos
The technical advice for the use and use of our products is based on our best knowledge and information, as a result of the tests carried out in our laboratories and our experience collected over the years at the customer's service.
ANGAR paints, will not be responsible for the problems caused by incorrect application of the products
If you want to know the PRICE OF THE EPOXY PRIMER OF TWO COMPONENTS FOR SOILS WITH DIFFICULT ANCHORING, you can consult it at the beginning of the page.
- Theoretical performance
- 8 - 10 m2 x kilo x mano
- 8 HORAS
- Disolvente Epoxi
- Useful of Application
- Brocha / Rodillo
- Cleanliness Tool
- Solvent Epoxi
- Dissolution of the first hand
- Entre el 5 % y el 10% Disolvente Epoxi
- Transparent or colorless
- Time of dried to a temperature of 25 ºC and a relative dampness of 50 %
- Curado Total a 20ºC : 7 Días
- Temperature of Application
- Temperatura del Soporte: Mínimo 10 ºC y Máximo 30ºC
- Proportion of the mixture
- 2 : 1 (Dos partes de Imprimación x 1 parte de catalizador)
- Humedad del soporte
- Inferior al 10 %
Me ha encantado es muy eficaz y he conseguido con esto que no se me levante la pintura del suelo, necesite algo de ayuda y la atención al cliente es super buena
Estupendo el producto, muy útil, me ha servido para que no se me levante la pintura encima de las baldosas del suelo. he probado otros productos pero ninguno tan efectivo como este, se nota que el material es directo de fábrica con calidad para profesionales, muchas gracias por todo.