EPOXY WATER PRIMER (Without Smell)
PRIMER SOILS EPOXY 2C TO WATER
Epoxy primer to water for concrete supports in warehouses and garages.
Recommended for poorly ventilated places due to its low odor and no toxicity .
Primer that is used as a connecting bridge on smooth concrete supports with very little porosity or difficult anchoring (ceramic, putty, polished concrete)
Primer for two-component waterborne floors
BUY PAINT FOR THE PRIMER OF SOILS WITH EPOXY TO THE WATER OF TWO COMPONENTS
BUY PRINTING FOR POLISHED OR FRACTIONED CONCRETE FLOORS OR LITTLE POROUS TILES TO IMPROVE THE ANCHORING OF THE FINISHING PAINT. EPOXY TO WATER THAT DOES NOT SMELL OF TWO COMPONENTS.
NATURE OF THE EPOXY PRIMER TO THE WATER OF TWO COMPONENTS
White water-based two-component primer, based on an epoxy-polyamide system.
FEATURES AND ADVANTAGES OF EPOXY PRIMER FOR SOILS TO WATER OF TWO COMPONENTS
This primer for water floors, is characterized by not contain any organic solvents so it is very suitable for application in rooms with poor ventilation , areas with risk of fire or areas where odors are not allowed (hospitals, slaughterhouses, feeding, etc.)
The water-based epoxy primer stands out for its excellent adhesion on supports that are difficult to anchor (ceramic, putty, polished concrete ...)
Being a water primer, it can be used to repaint floors that are already painted, and we do not know with what type of paint, so as not to risk that the new paint we are going to use, remove the old one and make the anchoring of the painting difficult. new.
WHERE CAN YOU APPLY THE PRIMER FOR EPOXY SOILS OF TWO COMPONENTS TO WATER?
Product used as adherent primer on smooth concrete supports with very little porosity, which are floated by helicopters or polished.
It is used in substrates with residual moisture that does not exceed 8%, although it should not be applied on wet surfaces or with water supply by capillarity. (If the support has moisture, use the primer for floors with humidity)
On highly polished surfaces, a light sanding is recommended prior to the application of the product.
HOW SHOULD THE EPOXY PRIMER BE APPLIED TO TWO COMPONENTS FOR WATER?
The binder system is supplied in an adequate proportion of mixture, which must be done in a homogeneous and complete way, avoiding the remains of products on the walls and bottom of the containers, stirring for at least 2 minutes.
The base of application must be clean, dry and exceeds oils, greases, grouts or aged paint in poor condition.
Some residual moisture below 10% is tolerated
You can add from 5% to 15% water to facilitate the application.
The environmental conditions necessary to apply the product require a minimum temperature of 10ºC and a relative humidity of less than 80%.
PRECAUTIONS WHEN USING TWO-COMPONENT WATER-BASED EPOXY PRIMER
Perform good ventilation of the premises and have a good extraction system.
Use active carbon mask, safety glasses and protective gloves during application.
PRESENTATION OF THE EPOXY PRIMER TO WATER 2C
It comes in containers of:
Component A: 5 and 15 kilos
Component B: 1 and 3 kilos
The technical advice for the use and use of our products is based on our best knowledge and information, as a result of the tests carried out in our laboratories and our experience collected over the years at the customer's service.
Pinturas ANGAR, SC will not be responsible for the problems caused by incorrect application of the products
If you want to know the PRICE OF THE PRIMER FOR SOILS OF EPOXY TO THE WATER OF TWO COMPONENTS, you can consult it at the beginning of the page.
- Theoretical performance
- 8 - 12 m2 x kilo x mano
- 8 Horas Mínimo
- Useful of Application
- Brocha / Rodillo / Airless
- Cleanliness Tool
- Dissolution of the first hand
- Del 5 % al 15 % Agua
- Juego 15 más 3 : Total 18 kilos
- Time of dried to a temperature of 25 ºC and a relative dampness of 50 %
- Curado total a 20 ºC : 10 Días
- Temperature of Application
- Temperatura del Soporte : Mínimo 10 ºC y Máximo 30 ºC
- Proportion of the mixture
- 5:1 (5 partes de Imprimación x 1 parte de catalizador)
- Useful life of the mixture
- 80 minutos a 20ºC
- Humedad del soporte
- Inferior al 10 %
Lo he utilizado para el suelo de mi garaje y el resultado ha sido increible, además no deja ningun olor y se nota que es de calidad
Pintura para suleos de garajes no porosos
Ideal para mi garaje ya que tiene muy poca ventilación, además la adherencia es genial.
Encantada con el producto y el resultado!