Painting use FOOD and SANITARY

IF YOU WANT TO KNOW MORE ABOUT THE PAINTING OF TWO COMPONENTS CLICK HERE

 IF YOU WANT TO KNOW MORE ABOUT THE CERTIFIED FOOD PAINT TO BE IN DIRECT CONTACT WITH FOOD, CLICK HERE

.

BUY EPOXY PAINT OF TWO COMPONENTS FOR FOOD AND SANITARY USE OF SOILS, CEILINGS, ETC ..

.

MARKING CE OF PAINTING EPOXY 2C FOOD USE

This food product has the CE mark following the guidelines of the harmonized European standard UNE-EN-1504-2: 2005 and UNE-EN-1504-8 Products and systems for the protection and repair of concrete structures.

Epoxy system suitable for contact with food, according to regulation 10/2011 of January 14, 2011

.

COMPOSITION OF EXPOXI 2C PAINT FOR FOOD USE

Epoxy system of two components without solvents, high resistance, formulated with components that are in the positive lists according to Royal Decree 1262/2005 of October 21, 2005 for materials that may be in contact with food.

Coating for surface protection of concrete with CE marking.

.

WHERE CAN I USE THE EPOXY PAINT OF TWO DOMINATORS FOR FOOD OR SANITARY USE?

In the industrial field for the protection of surfaces exposed to the attack of aggressive chemical products (waste water, alkaline or slightly acidic aqueous solutions).

Internal coating of deposits of products intended for FOOD (drinking water, oils, milk, syrups, etc.)

Due to the absence of solvents, it can be used in closed rooms without risk of explosion.

Repair of pipes for the transport of sanitation water.

For painting in general for the protection and repair of floors, ceilings, baseboards in food facilities, laboratories, health centers, residences, schools, dining halls, warehouses, etc.

For special use in slaughterhouses, canneries, dairies, cold rooms for storing food, operating rooms, veterinary centers, kitchens for bars and restaurants, school canteens, etc ...

.

HOW DO I HAVE TO APPLY THE EPOXY PAINT OF TWO COMPONENTS FOR FOOD USE?

-Surface steel: with abrasive blasting up to Sa3 scale with high roughness.

- Concrete: The application base must be clean, dry and free of old paints, grouts and curing liquids; it must have an open pore, which we will achieve by mechanical treatment (blasting or milling) or by other chemical treatments.

-The binder system is supplied in an adequate proportion of mixture, which must be done in a homogeneous and complete way, avoiding remaining product remains on the walls and bottom of the containers.

-We do not recommend partial blends.

-To apply high thicknesses and at the same time get a uniform film and a correct finish, the product should be applied with a double-boiler airless equipment and simultaneous mixing in nozzle.There are equipment whose application can be done hot.

-The product can also be applied by brush, trowel, roller, etc ... but presents difficulties due to the pasty consistency of the same, leaving irregular thickness finishes so it is necessary to apply two layers.

-The use of solvents for its application is not recommended, however ethyl alcohol can be used in a small proportion to facilitate the application (10% maximum) with which one of its qualities is lost in the application in enclosed areas, the risk of explosion.

-Do not apply at temperatures below 10 ºC

-The total hardening will not be achieved until after 7 days at temperatures close to 20 ºC.

-In concrete floors the pavement must be set (28 days minimum).

Performance: 400-500 g / m2 in 4 layers

(For more data on adhesion, permeability, absorption and drying, consult)

.

The technical advice for the use and use of our products is based on our best knowledge and information, as a result of the tests carried out in our laboratories and our experience collected over the years at the customer's service. 
Pinturas ANGAR, SC will not be responsible for the problems caused by incorrect application of the product

If you want to know the PRICE, OF THE EPOXY PAINTING OF TWO COMPONENTS FOR FOOD OR SANITARY USE, you can see it at the beginning of the page.

.

.