Floor Repair KIT Self-leveling epoxy mortar

IF YOU WANT TO READ MORE INFORMATION ABOUT 3D DECORATIVE FLOORS OR MIRROR EFFECT FLOORS CLICK HERE!

DO YOU NEED EPOXY PAINT TO REPAIR FLOORS OR AS A BASE COAT TO PAINT FLOORS THAT REQUIRE A HIGH THICKNESS?

COMPOSITION AND NATURE OF FLOOR REPAIR EPOXY

 Three-component epoxy set: Components A, B and selected silica filler, which can be used for various applications in concrete repair depending on the dosage between the epoxy binder and the accompanying filler.

FEATURES OF 2C SELF-LEVELLING EPOXY PAINT FOR FLOORS

The two-component epoxy coating for bases or undercoats on floors requiring high thickness is characterised by its lack of any solvents, low odour and rapid
start-up.

The high-thickness 2C epoxy base paint provides floors with great mechanical and chemical resistance, as well as exceptional adhesion and great hardness.

- Excellent adhesion on cementitious substrates.
- Great mechanical and chemical resistance.
- Its use as a final coat is not recommended.

TECHNICAL CHARACTERISTICS OF THE SELF-LEVELLING EPOXY MORTAR FOR REPAIRING FLOORS

Presentation: 4 kilos

Mixing proportions (by weight)

• A:B = 2:1 (epoxy binder to primer)

• (A+B) : Load = 1:1.5 mortar, pouring and self-leveling

• (A+B): Load = 1:4.3 (thixotropic repair mortar)

Epoxy binder density: 1.1 +- 0.05

Pot-life of epoxy binder: 10 minutes at 20ºC. The addition of filler for the preparation of the mortar lengthens the pot-life of the mixture.

WHERE CAN I APPLY HIGH THICKNESS 2C EPOXY BASE PAINT?

It is a self-levelling mortar that can be used as a pouring filler for anchoring metal elements.

In addition, by sprinkling a load with a larger granulometry, anti-slip bands can be obtained.

Fast-hardening repair mortar for spalling and cracking in concrete floors and structures. The fluidity of the binder allows the preparation of mortars for vertical surfaces and ceilings.

Paint to repair floors with holes, it is a self-leveling epoxy mortar, which acts as a higher quality cement for epoxy floors.

You can use this epoxy floor paint to repair pavements or create fillers to cover holes or uneven surfaces in the floor.

- Recommended system for food industries, healthcare areas, mechanical workshops, manufacturing and storage areas, ramps, loading docks, garages, etc.

HOW DO I APPLY THE BASE PAINT FOR HIGH THICKNESS GROUNDS?

HOW TO USE PAINT TO REPAIR FLOOR

- The binding system is supplied in an appropriate mixing ratio, in two containers, which must be mixed homogeneously and completely, avoiding product residues on the walls and bottom of the containers and the bottom of the containers with a low-revolution stirrer to avoid introducing air into the mixture.

- The mixture of aggregates or silica (Component C) will be made by slowly adding the perfectly homogenized binder system in a mechanical mixer, to achieve a homogeneous and regular mass.

The A+B mixture must be prepared in a separate container, which will also be the binder for the repair mortar. This binder will be used as a primer immediately after its preparation and the rest will then be used to prepare the repair mortar.

- The application base must be clean, dry and free of old paint, grout and curing liquids; it must have open pores, which can be achieved by mechanical treatment (blasting or milling) or by other chemical treatments.

- The humidity of the support must be less than 4%.

- Do not apply at temperatures below 10ºC.

- Complete hardening will not be achieved until after 7 days at temperatures not lower than 15-20ºC.

- Partial mixtures are not recommended 

- On concrete floors the pavement must be set (28 days minimum)

- Spread the first layer well with a metal trowel, smooth or notched.

TYPE OF AGGREGATE

The type of aggregate depends on the finish you want to leave; with a fine aggregate (0.1-0.3 mm) a smaller layer is left and a smoother finish, and with an aggregate of 0.3-0.7 mm the finish is rougher and the layer is thicker.
   
    

PRECAUTIONS WHEN USING SELF-LEVELLING REPAIR MORTAR PAINT

Provide good ventilation of the premises and have a good extraction system.

Use safety glasses and protective gloves during application. The use of a mask is recommended.

For more information, consult the Safety Data Sheet corresponding to the product.

PRESENTATION AND PACKAGING OF PAINT FOR SELF-LEVELLING FLOORS

It is presented in packages of:

Component A: 0.500 kilos Component B: 0.250 kilos Component C: 3.250 kilos

#BUY TWO-COMPONENT ADHESIVE EPOXY PAINT THAT IS USED AS A BASE TO FILL OR GROW BACKGROUND LAYERS THAT REQUIRE A HIGH THICKNESS. AND TO REPAIR CONCRETE FLOORS / WITHOUT SOLVENT/  

We guarantee the quality of our products in accordance with our general sales and supply conditions.

Our technical advice on use, expressed verbally, in writing or through tests, is offered in accordance with our current knowledge and experience. They constitute simple indications, which do not engage our responsibility, nor do they exempt you from the need to verify for yourself that the products we supply correspond to the procedures and objectives sought by you, by carrying out your own controls and tests. The application and use of the products are beyond our control, and consequently, they depend exclusively on your personal responsibility, and we cannot be held responsible for results other than those reflected here. Our recommendations in terms of safety do not prevent you from determining your own measures, adapted to the conditions of your own installations. We reserve the right to change the data contained herein, without prior notice, according to the technological evolution of the same.

If you want to know the price of two-component epoxy paint for making a base or undercoat or screeds on the floor, you can see it at the top of this page.