Esmalte Decoración MATE
INTUMESCENT painting up to R-120 for IRON Special paint
Esmalte Decoración MATE
INTUMESCENT painting up to R-120 for IRON Special paint

INTUMESCENT painting up to R-120 for IRON

€411.63
Tax included

PROGRESSIVE INTUMESCENCE SHEET COATING, FOR STEEL STRUCTURES

SEGUN NORMA UNE-EN13381-4

ENSAYOS DE RESISTENCIA AL FUEGO ENTRE 15 Y 120 MINUTOS EN HORNO CON CARGA SEGÚN ENSAYO EUROPEO UNE-ENV 13381-4:2005 CERTIFICADOS SEGÚN UNE-EN 1350 1-2:2004

Its mission is to delay the destructive action of a fire.

Reacts in the presence and contact of the flame, swelling, forming a multicellular insulation, extinguishing action.


Prolongs the stability of structures and construction elements subject to the high temperatures of a fire.

KILOS
  • 25 KG
Color
  • White
FINISH
  • Matee


<b>10</b> By purchasing this product, you will accumulate 20 points with our loyalty program. You can convert 20 points in your account into a coupon for a future purchase.

 

IF YOU WANT TO KNOW MORE ABOUT IGNÍFUGA PAINT, CLICK HERE

 

  

IF YOU WANT TO KNOW MORE ABOUT FIRE PROTECTIVE PAINTS, CLICK HERE

IF YOU WANT TO KNOW MORE ABOUT INTUMESCENT PAINTING, CLICK HERE

IF YOU WANT TO KNOW MORE ABOUT PAINT AND SYSTEMS FOR PASSIVE PROTECTION CONTINUE THE FIRE. CLICK HERE

.

BUY PAINTING AGAINST FIRE FOR IRON AND STEEL

.

BUY ENAMEL OR INTUMESCENT PAINTING FOR CERTIFIED GRASS R-15, R-30, R-60, R-120 ON STEEL STRUCTURES ACCORDING TO EUROPEAN UNE-EN1381-4

NATURE AND COMPOSITION OF INTUMESCENT CERTIFIED PAINTING FOR IRON

White solvent based coating, progressive intumescence fire protection to protect steel structures depending on the mass and the type of protected periphery.

FIRE CLASSIFICATION TESTS
* Tests of resistance to fire between 15 and 120 minutes in furnace with load according to European test UNE-ENV 13381-4: 2005.

Certificates according to UNE-EN 13501-2: 2004.


* Complies with standard UNE 48287-1.

.

In order to certify in the different minutes of resistance, they must send the beam to be coated so that we can specify the microns to be applied in the same to reach the desired INTUMESCENCE certificate.


TECHNICAL DATA

Color: White 90
Matte finish.
Specific weight: 1.39 ± 0.1.
Recommended dry thickness: According to official mass table (from 140μ to> 600μ per layer (*).
% Solids by volume: 62% ± 1%.
Yield per layer (600 μ): 1.03 m2./ lt = 0.74 m2./kg.
Drying time to the touch: 2 hours, at 20ºC and 60% RH.
Recoatable: 24 hours at 20 ° C and 60% RH.
Hardening: 5 days, at 20ºC and 60% RH.
Diluent indicated: STF (exclusively)
Application: Brush, roller and airless spray.
COV Supply: 360 gr / lt.


(*) - It depends on the application system chosen and the geometry of the elements to be protected. Avoid applying a thickness that can lead to leaks and drips due to excess layer.

.

CHARACTERISTICS AND ADVANTAGES OF THE INTENSIVE CERTIFICATE PAINT OR ENAMEL FOR IRON OR STEEL

FEATURES OF DRY FILM

Reacts in contact with the flame or high temperatures, swelling and forming a foam
Multicellular high insulation capacity.
Not flammable. Once the work is done, it calcines without producing or communicating the flame.

.


FIELDS OF APPLICATION OF PAINTING OR ENAMELING FOR INTUMESCENT CERTIFIED IRON

Protection against fire of all kinds of structural steel elements.
Due to its special characteristics, it is used in the passive protection against fire of structural elements of buildings, both private and public (homes, apartments, offices, hotels, hospitals, schools, supermarkets, shows, stairs, etc.). The requirements of the Technical Building Code.
In the habitat areas of a ship.
Particularly important is its use for the passive fire protection of the industry in general (industrial warehouses, supports, tanks, silos, etc.), complying with the requirements of the Fire Safety Regulations in Industrial establishments.

.

HOW DO I APPLY INTUMESCENT CERAMIC ENAMEL OR PAINT FOR STEEL?

PRIOR SURFACE TREATMENT


Metal surfaces: They must be primed in advance with products of high anticorrosion capacity, compatible with the intumescent coating and of a proven fire-retardant nature, classified as non-flammable according to UEN-EN 13501-1: 2007 + A1-2010


Non-metallic surfaces: On wood, plaster, cement, etc., please consult our Technical Department.

METHOD OF APPLICATION

Thoroughly homogenize the contents of the package, preferably with a mechanical stirrer.

The product is served ready for use. To facilitate its application to airless spray gun, it can be diluted with a maximum of 10% FTS. (Do not use other solvents).


Brush: Only for touch-ups and small areas. Apply without diluting.


Roller: Apply undiluted. Use long-pile woolen rollers.


Air gun: From pressure boiler. Dilute with 5 to 15% FTS.


Pressure, 4 Kgs / cm2. Nozzles 2.6 to 2.8 mm. (I.e.


Airless spray (*): Dilute with 0 to 10% FTS.


Equipment capable of providing a free flow rate higher than 5.8 lts / min., With a maintained pressure greater than 120 Kgs / cm2. Nozzles 0.025 to 0.031 ".


Adjust the nozzle angle to the size of the profiles to be coated.


The lining should be used indoors, protected from moisture, weather,
Condensations, etc.

In indoor environments with moderate environmental aggression, it is highly recommended to apply one or two layers of anticorrosive finish enamel classified as non-flammable.


In exterior elements or in aggressive environmental conditions, it is necessary to completely seal the surface with a Polyurethane 2C (Consult our Technical Department).


The intumescent coating should not be applied when the environmental conditions of the element to be protected are not adequate:

Temperatures below 10 ° C, humidities above 80%, condensation conditions at any temperature and ambient humidity, or temperature of the substrate not higher than 3 ° C to that of the dew point.


(*) WIWA pneumatic pistols type 1132 and 4432.
Electric or gasoline guns, type AIRLESSCO, models 6100 and 9100.

.


SAFETY AND HYGIENE when applying Coat INTUMESCENT CERTIFICATE FOR STEEL


The application must be carried out with abundant air supply or with ventilation systems prepared for this purpose.
The usual personal protective equipment should be used to avoid ingestion, inhalation or skin contact. Normal fire precautions should be taken during use.
Keep containers tightly closed after use. Do not empty into drains.
Storage stability: 1 year in its original closed containers and in good storage conditions.

.



PRESENTATION OF INTUMESCENT PAINTING


It comes in packaging of: 5 KGS / 25 KGS

OBSERVATIONS


We guarantee the quality of our products according to our general conditions of sale and supply. Our technical advice for use, expressed orally, in writing or by trial, is offered in accordance with our current knowledge and experience. They are simple indications that do not compromise our responsibility, nor do they exempt from the need to verify by you. That the products we supply correspond to the procedures and objectives sought by you, carrying out your own controls and tests. The application and use of the products are beyond our control, and therefore, depend exclusively on your personal responsibility, and can not be responsible for results other than those reflected here. Our recommendations on safety do not prevent you from determining your own measures, adapted to the
Conditions of its facilities. We reserve the right to vary the information contained herein, without prior notice, according to the technological evolution of the same.

The technical advice for the use and use of our products are given according to our best knowledge and information, fruit of the tests carried out   In our laboratories and our experience collected over the years at the service of the client.  

ANGAR, SC will not be responsible for the problems caused by incorrect application or misuse of our products.

.

If you want to know the PRICE OF PAINTING OR ENAMELLING CERTIFICATE INTENSIVE IRON R-15, R-30, R-60, R-120, you can see it at the top of the page

..

.

Theoretical performance
0.74 M2 X KG
Repainted
24 hours
FINISH
Dull
Solvent
STF
Useful of Application
BRUSH / ROLLER / AIRLESS
Color
WHITE
Solid in weight
62 % ± 1 %.
certificado
INTUMESCENTE HASTA R-120 MINUTOS
Humedad del soporte
Inferior al 10 %
STOFIRE H
500 Items

Reviews Reviews (0)

Based on 0 reviews - 0 1 2 3 4 0/5
Pinterest

Portes Gratis Angar para pedido + 75 €