2c Polyurethane Swimming Pool Paint (Membrane, Tiles, Pvc)
2C Acrylic POLYURETHANE ENAMEL for TILES, TILES and PVC
Waterproof paint for pools of tiles, gresite, tiles, pvc or after applying liquid waterproofing membrane of polyurethane.
Enamel that provides great adhesion and flexibility, great hardness and chemical and mechanical resistance.
Product customizationDon't forget to save your customization to be able to add to cart
IF YOU WANT MORE INFORMATION ON HOW TO CORRECTLY PAINT A POOL, YOU CAN READ THIS ARTICLE FROM OUR BLOG
COMPOSITION OF THE ENAMEL OR PAINT FOR POOLS OF TILES, TILES OR PVC
Two-component system based on a crosslinked hydroxylated acrylic resin system with aliphatic polyisocyanates.
ADVANTAGES OF THE ENAMEL OR PAINTING FOR TILES AND TILES OF TWO COMPONENTS
Two-component polyurethane paint that provides good weather resistance and very good stability in ultraviolet light.
Tile paint that also stands out for its good flexibility, color retention and abrasion resistance, with great covering power.
Provides great hardness and chemical and mechanical resistance to the tiles painted with this paint.
Waterproof paint for small leaks or fissures of less than 1mm.
Two-component paint, which does not fall off over time, or spoil. If you want the best quality for your tiles, don't risk it, use a two-component paint.
WHERE TO USE THE ENAMEL OR PAINT FOR TILES AND TILES?
Paint to change the appearance of the tiles in your POOL, without having to make major reforms.
Paint indicated to protect and decorate all kinds of metal supports, wood, glass, tiles, some plastic PVC surfaces, also on light metals (Aluminum, galvanized, etc. ..).
HOW TO USE DECORATIVE PAINT OR ENAMEL FOR TILES AND TILES?
-Remove the material very well, the surfaces to be painted must be dry, clean and consistent
Mix the two components and homogenize the contents of the container, stirring thoroughly.
Let stand for about five minutes, and then dilute conveniently with polyurethane solvent.
We recommend waiting between 24 and 72 hours, after emptying the pool, for a perfect drying of the pool, before painting.
And wait again between 5 days and two weeks, after painting or varnishing it to refill the pool with water, for a correct application. (The longer we can leave it drying, the better)
-The surfaces to be painted must be free of dust, lime, grease and old, well-dried paints.
-If the surface is not very porous, it is recommended to wear it with a chemical or mechanical abrasive for the perfect anchorage of the paint. (Especially in the case of ceramic tiles)
-Homogenize the contents of the container by stirring thoroughly.
-The application can be done with a brush, roller (we recommend a roller with a hair pole)
In the case of ceramic tiles and gresites, should be applied a first coat of i epoxy mprimación to the solvent for non - porous surfaces.
-First coat, and will be applied by spreading the paint well, to avoid thick layers, diluted between 20% and 25% with polyurethane solvent.
- The second coat diluted to 10% in case of ceramic tiles and gresites
-It is recommended to apply a third coat in case of major leaks, when a perfect waterproofing is desired
-To achieve a good adhesion between layers, it is not necessary to allow more than 24 hours to elapse, but the layers must be allowed to dry well, to avoid the appearance of bubbles or blisters.
-Allow to dry properly before painting and before embalming with water (minimum 72 hours) We recommend waiting 7 days before filling it
On clean and degreased surfaces, eliminating any presence of oxidation.
For any other support: Consult.
In good condition.- Clean of fats, oils, dirt, to later apply as needed.
In poor condition.- Remove the paint in poor condition and proceed to apply our product.
PRECAUTIONS WHEN USING TWO COMPONENT POLYURETHANE DECORATIVE ENAMEL OR PAINT PAINT.
If you have the pool painted with chlorinated rubber or acrylic solvent paint, this paint may remove old paint.
You must always repaint with two-component polyurethane paint, (another type of paint, it will not have the strength to grip in this paint)
TO PAINT FIBERGLASS POOLS, YOU MUST SAND IT BEFORE AND OPEN THE PORE.
Carry out good ventilation and have a good extraction system.
Use activated carbon mask, safety glasses and protective gloves during application.
Do not apply thick layers
Let the paint dry between layers, so that no blisters or bubbles appear.
We recommend not painting in the central hours of the day. in order not to cause a very fast drying when the support is very hot. (Best to apply first thing in the morning)
Avoid applying with a very high relative humidity in the environment or with pink, contact with water, prevents a perfect anchoring of the paint
It should not be mixed or diluted with any other product or substance since the base characteristics can be altered.
It is presented in packages of:
Component A: 3 kilos and 15 kilos.
Component B: 0.75 kilos and 3 kilos.
PAINT FOR PAINTING AND WATERPROOFING TILE AND POOL POOLS
We guarantee the quality of our products in accordance with our general conditions of sale and supply.
The technical advice for the use and use of our products is given according to our best knowledge and information, the result of the tests carried out in our laboratories and our experience gathered over the years at the customer's service.
BUY PAINTING FOR POOLS OF TILES, TILES, GRESITES PVC OR SANDED FIBERGLASS.
BICOMPONENT PAINTING THAT GRIPS IN ANY TYPE OF TILE and TILE, BOTH INTERIOR AND EXTERIOR.
ENAMEL FOR PAINTING TILES AND TILES OF BOTH FLOOR AND WALL.
If you want to know the PRICE OF THE PAINTING FOR TILES AND TILES, BOTH INTERIOR AND EXTERIOR, you can consult it at the beginning of this page.
- 8 Hora Mínimo / 24 Horas Máximo (para una perfecta adherencia)
- Theoretical performance
- Between 6 and 10 square meters per Kilo and Hand (Depending on the media, whether it is new or already painted)
- Brightness / Matte / Satin
- Disolvente Poliuretano
- Useful of Application
- BRUSH / ROLLER / AIRLESS
- Cleanliness Tool
- Solvent Polyurethane
- Dissolution of the first hand
- Between 20 % and 25 %
- Dissolution in the second hand
- 10% Solvent
- Juego 3.075 kgs / Juego de 18 kgs
- Time of dried to a temperature of 25 ºC and a relative dampness of 50 %
- TOUCH: 1 hour
- Temperature of Application
- Humedad del soporte, inferior al 10%
- Proportion of the mixture
- 4: 1 (4 parts of polyurethane catalyst x 1)
- Flame retardant B-s2, d0
- Humedad del soporte
- Inferior al 10 %
The customer has rated the product but has not posted a review, or the review is pending moderation